Sections

TX IO power supply

• Open the TX IO case by unscrewing the 4 cover screws.

• Externally power your TX IO (between 7.5 and 24VDC). If you use our 12V power supply, connect your power supply to the POWER terminal of the receiver.

•Red wire connected to the V+ terminal block

•Black wire connected to the 0V terminal block

Access to the TX IO configuration server

The procedure for accessing the TX IO configuration server is identical to that of the receiver. The default address for accessing the TX IO server is 192.168.77.77 (please avoid use on Microsoft Edge and favor use on Google Chrome).

Selecting local control mode

Select the D2D operating mode from the CONFIG TX IO tab . Once selected, restart your TX IO so that the mode change is taken into account using the Reboot button from the TX IO server Admin tab

Declaration and configuration of sensor alarm thresholds

In the CONFIG D2D tab, you must declare the sensors you want to pair to the TX IO. The procedure is the same as when you declare sensors on a receiver

Relay configuration

In the CONFIG TX IO tab, the relays can be associated with the alarm thresholds of the sensors that we have just configured.

To do this, for each relay select:

• The LoRa ID of the configured sensor

• The relay mode: normally closed or normally open

Normally closed : corresponds to a closed rest state. When the status is 0, the relay is closed. When the status is 1, the relay is open.

Normally open : corresponds to an open rest state. When the status is 0, the relay is open. When the status is 1, the relay is closed.

• The type of alarm to trigger a relay.

Activation of sensors

The activation of the sensors is done in the same way when pairing the sensors to the receiver.

Validation of reception of sensor information

In the STATUS tab , in the Transmitter Network section, the frames from the sensors that you have just activated must be sent at the periodicity that has been configured. This tab allows you to validate the correct reception of sensor frames. We recommend using this page as an on-site audit tool, to validate that RSSI levels for receiving probes are good.

Viewing output status

In the STATUS tab in the Outputs section you can see the relay status display ON or OFF and the number of times the status has been switched from the TX IO power supply. You can test the relay status by clicking the Toggle Relay button. The relay activates for one second.

The TX IO offers Enless integrators different control possibilities. As a reminder, the TX IO has 2 contact-dry inputs and 4 controllable relay outputs. It can be used in 3 distinct modes which will be configurable from the server embedded in the transmitter.

By default, the TX IO is delivered ready to be used in remote control mode.

Step 1 : Configuring TX IO from the RX server

The configuration of the TX IO will be done from the receiver server with which the TX IO will communicate.

Below are the steps for configuring the TX IO.

Step 2 : TX IO Activation

Once declared on the receiver server and configured, you will need to activate the TX IO to pair it with the receiver. Below are the steps for activating the TX IO.

Step 3 : Validation of TX IO activation

Validate that the TX IO communicates with the receiver.

Step 4 : Relay control

Optional step: Displaying the status of inputs/outputs

In the STATUS tab you can see the status display of the digital inputs and the counts since power-up. At the bottom of the tab you can see the relay status display ON or OFF and the number of times the status has been switched from the TX IO power supply.

You can test the relay status by clicking the Toggle Relay button. The relay activates for one second.

TX IO power supply

• Open the TX IO case by unscrewing the 4 cover screws.

• Externally power your TX IO (between 7.5 and 24VDC). If you use our 12V power supply, connect your power supply to the POWER terminal of the receiver.

•Red wire connected to the V+ terminal block

•Black wire connected to the 0V terminal block

Access to the TX IO configuration server

for accessing the TX IO configuration server is identical to that of the receiver. The default address for accessing the TX IO server is 192.168.77.77 (please avoid use on Microsoft Edge and favor use on Google Chrome).

Selecting local control mode

Select the Local Control operating mode from the TX IO config tab . Once selected, restart your TX IO so that the mode change is taken into account using the Reboot button from the TX IO server Admin tab.

Configuring TX IO parameters from its server

In the CONFIG TX IO tab , configure your relays by selecting for each relay:

• Input: input 1 or input 2

• The relay mode: normally closed or normally open

Normally closed : corresponds to a closed rest state. When the status is 0, the relay is closed. When the status is 1, the relay is open.

Normally open : corresponds to an open rest state. When the status is 0, the relay is open. When the status is 1, the relay is closed.

• The delay: 1 sec, 5 sec, 10 sec, 30 sec, 60 sec or 120 sec.

Viewing the status of inputs and outputs

In the STATUS tab you can see the status display of the digital inputs and relays, as well as the number of status changes since power-up. You can test the status of the relays by clicking on the Toggle Relay button. The selected relay activates for one second. The TX IO is now configured, you can power it off.

Declaration and configuration of TX IO from the receiver server

Activation of TX IO

Validation of TX IO activation from the receiver server

In the CONFIG TX tab, refresh your browser page. A validation sticker should appear in front of the TX IO that you have just activated.

In the NETWORK tab, the TX IO frames that you have just powered must be sent at the periodicity that has been configured. This tab allows you to validate the correct reception of the TX IO frames.