📎Safety

Safety recommendations

• The safety of Enless products can only be guaranteed if they are used for their intended purpose. They must only be serviced by qualified persons

• Risk of explosion if sensor batteries are replaced with an incorrect reference. Please refer to the appendix for replacing sensor batteries.

• The sensors must be installed in an adequately ventilated environments to ensure there is no danger of internal overheating. They must not be covered with things such as newspapers, cloth, curtains, etc

• Sensors must never be exposed to high temperature sources (E.g.: attached to heating equipment, etc.)

• Do not place the sensors near objects that generate flames (E.g.: candles, blowpipes, etc.)

• The sensors must not be exposed to aggressive chemical agents or solvents that may damage plastic or corrode metal parts

• The ANT-REN-SMA LR 915 MHz 1000-101 used with LoRa receivers, repeater, TX MODBUS should be installed indoor only.

Reminder relating to the use of the TX PULSE ATEX 600-037 transmitter

As required by the ATEX 1999/92/EC Directive, only persons trained for working in hazardous areas are authorised to install the TX PULSE ATEX 600-037 transmitter. The TX PULSE ATEX 600-037 transmitter must not be modified in any way

Special conditions for safe operation

When used with a gas meter, the output wires of the TX PULSE ATEX 600-037 transmitter must be connected to certified intrinsically safe equipment. This combination must be compatible with the Uo, Io, Po, Co, Lo intrinsic safety regulations specified on the label attached to the transmitter.

Certification

The TX PULSE ATEX 600-037 transmitter is ATEX certified:

II 1 G

Ex ia IIC T3 Ga

LCIE 14 ATEX 3013 X

-20°C ≤ Tamb ≤ +55°C

Battery: 3,6 V Ramway ER34615 only.

Uo:3,9 V ; Io : 11,47 mA ; Po : 11,18 mW ; Co : 617 μF : Lo : 270 mH.

Battery

The TX PULSE ATEX 600-037 transmitter is delivered with a RAMWAY ER34615 model battery. Only the RAMWAY ER34615 battery can be used with the TX PULSE ATEX 600-037 transmitter. These batteries can be obtained from Enless Wireless - 45 ter avenue de Verdun 33520, Bruges (France). Telephone: [phone] – email: [e-mail]

WARNING - POTENTIAL RISK OF STATIC DISCHARGE

The TX PULSE ATEX 600-037 transmitter must only be cleaned using a damp cloth.

Legal information for 915MHz devices

This device complies with part 15 of the FCC Rules and with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-003(B) / NMB-003(B)